 |
|
Error codesThe list shows the error codes for optical drives with a short description.Common errors (displayed in bold) are explained in detail. Sense code 00 (No Sense) 00000 NO ADDITIONAL SENSE INFORMATIONSense code 01 (Recovered Error) 10B00 WARNING 10B01 WARNING - SPECIFIED TEMPERATURE EXCEEDED 10B02 WARNING - ENCLOSURE DEGRADED 11700 RECOVERED DATA WITH NO ERROR CORRECTION APPLIED 11701 RECOVERED DATA WITH RETRIES 11702 RECOVERED DATA WITH POSITIVE HEAD OFFSET 11703 RECOVERED DATA WITH NEGATIVE HEAD OFFSET 11704 RECOVERED DATA WITH RETRIES AND/OR CIRC APPLIED 11705 RECOVERED DATA USING PREVIOUS SECTOR ID 11707 RECOVERED DATA WITHOUT ECC - RECOMMEND REASSIGNMENT 11708 RECOVERED DATA WITHOUT ECC - RECOMMEND REWRITE 11709 RECOVERED DATA WITHOUT ECC - DATA REWRITTEN 11800 RECOVERED DATA WITH ERROR CORRECTION APPLIED 11801 RECOVERED DATA WITH ERROR CORR. & RETRIES APPLIED 11802 RECOVERED DATA - DATA AUTO-REALLOCATED 11803 RECOVERED DATA WITH CIRC 11804 RECOVERED DATA WITH L-EC 11805 RECOVERED DATA - RECOMMEND REASSIGNMENT 11806 RECOVERED DATA - RECOMMEND REWRITE 13700 ROUNDED PARAMETER 17301 POWER CALIBRATION AREA ALMOST FULLSense code 02 (Not Ready) 20400 LOGICAL UNIT NOT READY, CAUSE NOT REPORTABLE 20401 LOGICAL UNIT IS IN PROCESS OF BECOMING READY 20402 LOGICAL UNIT NOT READY, INITIALIZING CMD. REQUIRED 20403 LOGICAL UNIT NOT READY, MANUAL INTERVENTION REQUIRED 20404 LOGICAL UNIT NOT READY, FORMAT IN PROGRESS 20407 LOGICAL UNIT NOT READY, OPERATION IN PROGRESS 20408 LOGICAL UNIT NOT READY, LONG WRITE IN PROGRESS 23000 INCOMPATIBLE MEDIUM INSTALLED 23001 CANNOT READ MEDIUM - UNKNOWN FORMAT 23002 CANNOT READ MEDIUM - INCOMPATIBLE FORMAT 23003 CLEANING CARTRIDGE INSTALLED 23004 CANNOT WRITE MEDIUM - UNKNOWN FORMAT 23005 CANNOT WRITE MEDIUM - INCOMPATIBLE FORMAT 23006 CANNOT FORMAT MEDIUM - INCOMPATIBLE MEDIUM 23007 CLEANING FAILURE 23A00 MEDIUM NOT PRESENT No disc inserted 23A01 MEDIUM NOT PRESENT - TRAY CLOSED 23A02 MEDIUM NOT PRESENT - TRAY OPEN 23E00 LOGICAL UNIT HAS NOT SELF-CONFIGURED YETSense code 03 (Medium Error) 30200 NO SEEK COMPLETE 30600 NO REFERENCE POSITION FOUND 30C00 WRITE ERROR 30C07 WRITE ERROR - RECOVERY NEEDED 30C08 WRITE ERROR - RECOVERY FAILED 30C09 WRITE ERROR - LOSS OF STREAMING Buffer underrun: a CD recorder will report this error when the buffer is empty while burning a CD. In most cases this is caused by the source drive which is not fast enough to feed the recorder with data. A solution is to buy another drive or to burn the CD via an image file. This error can also occur when the interface is unable to transfer the data fast enough. This can happen when you are using the USB interface. 30C0A WRITE ERROR - PADDING BLOCKS ADDED 31100 UNRECOVERED READ ERROR 31101 READ RETRIES EXHAUSTED 31102 ERROR TOO LONG TO CORRECT 31105 L-EC UNCORRECTABLE ERROR The drive is unable to read a data sector on the disc. This is caused by a defective (scratched) disc. 31106 CIRC UNRECOVERED ERROR 3110F ERROR READING UPC/EAN NUMBER 31110 ERROR READING ISRC NUMBER 31500 RANDOM POSITIONING ERROR 31501 MECHANICAL POSITIONING ERROR 31502 POSITIONING ERROR DETECTED BY READ OF MEDIUM 33100 MEDIUM FORMAT CORRUPTED 33101 FORMAT COMMAND FAILED 35100 ERASE FAILURE 35700 UNABLE TO RECOVER TABLE-OF-CONTENTS 37200 SESSION FIXATION ERROR 37201 SESSION FIXATION ERROR WRITING LEAD-IN 37202 SESSION FIXATION ERROR WRITING LEAD-OUT 37300 CD CONTROL ERROR 37302 POWER CALIBRATION AREA IS FULL 37303 POWER CALIBRATION AREA ERROR 37304 PROGRAM MEMORY AREA UPDATE FAILURE 37305 PROGRAM MEMORY AREA IS FULLSense code 04 (Hardware Error) 40017 CLEANING REQUESTED 40500 LOGICAL UNIT DOES NOT RESPOND TO SELECTION 40800 LOGICAL UNIT COMMUNICATION FAILURE 40801 LOGICAL UNIT COMMUNICATION TIME-OUT 40802 LOGICAL UNIT COMMUNICATION PARITY ERROR 40900 TRACK FOLLOWING ERROR 40901 TRACKING SERVO FAILURE 40902 FOCUS SERVO FAILURE 40903 SPINDLE SERVO FAILURE 40904 HEAD SELECT FAULT 41B00 SYNCHRONOUS DATA TRANSFER ERROR 43E01 LOGICAL UNIT FAILURE 43E02 TIMEOUT ON LOGICAL UNIT 440NN DIAGNOSTIC FAILURE ON COMPONENT NN (80H-FFH) 44400 INTERNAL TARGET FAILURE 44600 UNSUCCESSFUL SOFT RESET 44700 SCSI PARITY ERROR 44A00 COMMAND PHASE ERROR 44B00 DATA PHASE ERROR 44C00 LOGICAL UNIT FAILED SELF-CONFIGURATION 45300 MEDIA LOAD OR EJECT FAILED 46500 VOLTAGE FAULTSense code 05 (Illegal Request) 50011 AUDIO PLAY OPERATION IN PROGRESS 50700 MULTIPLE PERIPHERAL DEVICES SELECTED 51A00 PARAMETER LIST LENGTH ERROR 52000 INVALID COMMAND OPERATION CODE The software is using a command which is not supported by the drive. 52100 LOGICAL BLOCK ADDRESS OUT OF RANGE 52101 INVALID ELEMENT ADDRESS 52400 INVALID FIELD IN CDB The software is using a command with incorrect parameters. 52500 LOGICAL UNIT NOT SUPPORTED 52600 INVALID FIELD IN PARAMETER LIST 52601 PARAMETER NOT SUPPORTED 52602 PARAMETER VALUE INVALID 52603 THRESHOLD PARAMETERS NOT SUPPORTED 52604 INVALID RELEASE OF ACTIVE PERSISTENT RESERVATION 52700 WRITE PROTECTED 52701 HARDWARE WRITE PROTECTED 52702 LOGICAL UNIT SOFTWARE WRITE PROTECTED 52703 ASSOCIATED WRITE PROTECT 52704 PERSISTENT WRITE PROTECT 52705 PERMANENT WRITE PROTECT 52B00 COPY CANNOT EXECUTE SINCE HOST CANNOT DISCONNECT 52C00 COMMAND SEQUENCE ERROR 52C03 CURRENT PROGRAM AREA IS NOT EMPTY 52C04 CURRENT PROGRAM AREA IS EMPTY 53008 CANNOT WRITE - APPLICATION CODE MISMATCH 53009 CURRENT SESSION NOT FIXATED FOR APPEND 53900 SAVING PARAMETERS NOT SUPPORTED 53D00 INVALID BITS IN IDENTIFY MESSAGE 54300 MESSAGE ERROR 55302 MEDIUM REMOVAL PREVENTED 56300 END OF USER AREA ENCOUNTERED ON THIS TRACK 56301 PACKET DOES NOT FIT IN AVAILABLE SPACE 56400 ILLEGAL MODE FOR THIS TRACK The software is using a command which is invalid for the type of disc (for example using a data read command on an audio disc). 56401 INVALID PACKET SIZE 56F00 COPY PROTECTION KEY EXCHANGE FAILURE - AUTHENTICATION FAILURE 56F01 COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT PRESENT 56F02 COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED 56F03 READ OF SCRAMBLED SECTOR WITHOUT AUTHENTICATION The software is trying to read data from a locked DVD Video disc. 56F04 MEDIA REGION CODE IS MISMATCHED TO LOGICAL UNIT REGION 56F05 DRIVE REGION MUST BE PERMANENT/REGION RESET COUNT ERROR 57203 SESSION FIXATION ERROR - INCOMPLETE TRACK IN SESSION 57204 EMPTY OR PARTIALLY WRITTEN RESERVED TRACKSense code 06 (Unit Attention) 60A00 ERROR LOG OVERFLOW 62800 NOT READY TO READY CHANGE, MEDIUM MAY HAVE CHANGED 62801 IMPORT OR EXPORT ELEMENT ACCESSED 62900 POWER ON, RESET, OR BUS DEVICE RESET OCCURRED 62901 POWER ON OCCURRED 62902 SCSI BUS RESET OCCURRED 62903 BUS DEVICE RESET FUNCTION OCCURRED 62904 DEVICE INTERNAL RESET 62A00 PARAMETERS CHANGED 62A01 MODE PARAMETERS CHANGED 62A02 LOG PARAMETERS CHANGED 62A03 RESERVATIONS PREEMPTED 62F00 COMMANDS CLEARED BY ANOTHER INITIATOR 63B0D MEDIUM DESTINATION ELEMENT FULL 63B0E MEDIUM SOURCE ELEMENT EMPTY 63B0F END OF MEDIUM REACHED 63B11 MEDIUM MAGAZINE NOT ACCESSIBLE 63B12 MEDIUM MAGAZINE REMOVED 63B13 MEDIUM MAGAZINE INSERTED 63B14 MEDIUM MAGAZINE LOCKED 63B15 MEDIUM MAGAZINE UNLOCKED 63F00 TARGET OPERATING CONDITIONS HAVE CHANGED 63F01 MICROCODE HAS BEEN CHANGED 63F02 CHANGED OPERATING DEFINITION 63F03 INQUIRY DATA HAS CHANGED 65A00 OPERATOR REQUEST OR STATE CHANGE INPUT 65A01 OPERATOR MEDIUM REMOVAL REQUEST 65A02 OPERATOR SELECTED WRITE PROTECT 65A03 OPERATOR SELECTED WRITE PERMIT 65B00 LOG EXCEPTION 65B01 THRESHOLD CONDITION MET 65B02 LOG COUNTER AT MAXIMUM 65B03 LOG LIST CODES EXHAUSTED 65D00 FAILURE PREDICTION THRESHOLD EXCEEDED 65DFF FAILURE PREDICTION THRESHOLD EXCEEDED (FALSE) 65E00 LOW POWER CONDITION ON 65E01 IDLE CONDITION ACTIVATED BY TIMER 65E02 STANDBY CONDITION ACTIVATED BY TIMER 65E03 IDLE CONDITION ACTIVATED BY COMMAND 65E04 STANDBY CONDITION ACTIVATED BY COMMAND |